Guide

Phone signal strength in dBm: what the numbers mean

By Gaming Gangs · Updated 20 October 2026

Signal bars are a rough guide, and different phones draw them differently. The number behind them, in dBm, is more exact. This guide shows what the numbers mean, where to find yours, and what to do when the number is low.

What dBm means

dBm tells you how much radio power your phone receives from the mobile tower. The amounts are tiny, so the numbers are negative. The rule is simple: the closer to zero, the stronger the signal. A reading of -70 dBm is stronger than -100 dBm.

The scale is not even. Every 10 dBm step is ten times more or less power, so -90 dBm is ten times weaker than -80 dBm, and -100 dBm is a hundred times weaker. That is why a change that looks small on screen can matter a lot.

The 4G and 5G chart

On 4G and 5G, the number to watch is called RSRP, the power of the tower's reference signal. This table is a rule of thumb. Phone makers and carriers draw the lines in slightly different places.

RSRPWhat it means
-80 dBm or betterExcellent. Fast, steady data and clear calls.
-80 to -90 dBmGood. Most things work well.
-90 to -100 dBmFair. It works, but speeds can drop, especially when the tower is busy.
-100 to -110 dBmPoor. Slow data, shaky video calls, and some dropped connections.
Below -110 dBmVery weak. Often no service or unusable data.

These ranges are for 4G and 5G. Older 2G and 3G networks report on a different scale, so do not compare their numbers with this chart.

Why bars are not a standard

There is no rule for how many bars a signal should get. One phone maker may show four bars at -95 dBm while another shows two. Two phones side by side can show different bars for the same signal. So comparing bars between phones tells you little, but comparing dBm does.

RSRQ and SINR in one minute

RSRQ is signal quality, measured in dB. It usually runs from about -3 (very good) to -20 (poor). It tells you how clean the signal is compared with the noise and the other people using the same tower. A tower can have strong power and still show poor RSRQ when it is very busy.

SINR compares the useful signal with the noise and interference around it, also in dB. Higher is better: above about 13 is good, and 0 or below is poor. A high SINR usually goes with faster data. Not every phone shows RSRQ and SINR in its normal menus.

Where to see the number on Android

  1. Open Settings.
  2. Tap About phone.
  3. Tap SIM status. On some phones it is called Status or Status information. With two SIMs, pick the one you want.
  4. Look for Signal strength.

You will see something like "-95 dBm 45 asu". The asu number is the same reading in another unit. On 4G, asu is simply dBm plus 140. Menu names differ by phone maker, and a few phones hide this screen. Many phones also show the number in the hidden testing menu, which you open from the dialler with *#*#4636#*#*. It does not work on every phone.

How to use the number

Take a reading in the room where you use your phone most. If it shows -105 dBm or lower, no setting will help much: moving, Wi-Fi calling or asking your carrier will. If it shows -80 dBm and the internet is still slow, the problem is probably a busy tower or poor quality, not a lack of signal. The number tells you which of the two you are dealing with.

How to get a better signal

You cannot change the tower, but you can change where you stand and how you hold the phone:

  • Move near a window or go outside. Walls, concrete and metal-coated glass block radio waves.
  • Try a higher floor. Signal is often cleaner above the clutter of the street.
  • Do not cover the antenna. Phone antennas sit around the edges. A tight grip, a thick case or a metal plate on the back can weaken the signal.
  • Compare spots. Stand in each spot for about half a minute, note the dBm, and pick the best one. Put your desk, bed or router there if you can.
  • Reconnect. Turn airplane mode on for ten seconds and off again. Sometimes the phone is stuck on a faraway tower.
  • Use Wi-Fi calling. If your carrier offers it, calls over Wi-Fi can fix poor signal indoors.

If the signal is poor everywhere in your home, tell your carrier. If 5G keeps dropping to 4G, read why your phone keeps switching between 5G and 4G.

Where MaxBars fits

The Signal finder in MaxBars shows your live signal strength with a graph and optional beeps. Walk slowly around a room and watch the graph or listen to the beeps, and you will find the strongest spot quickly. The speed test and Best Mode Here let you compare network modes where you are.

To be clear: no app can make the signal itself stronger, and MaxBars does not try. It cannot add signal, make a weak network stronger, or give you 5G where your phone, plan or carrier does not offer it. It shows you the signal and lets you choose which network types your phone may use, such as 5G + 4G, 4G only or Auto. The guide to LTE only mode explains when the 4G only choice helps.

Questions and answers

What is a good dBm signal for a phone?

For 4G and 5G, -80 dBm or closer to zero is excellent and -80 to -90 is good. Below -110 dBm is very weak, and you may have little or no service.

Is -100 dBm a bad signal?

It sits between fair and poor. Calls and messages usually work, but video, maps and big downloads can be slow.

Why does my dBm number keep changing?

Signal moves from second to second as you move, as people walk past and as the network changes. Swings of a few dBm are normal, so watch it for half a minute before you decide.

Can an app boost my phone signal?

No. Signal depends on the tower, where you stand, what is in the way and your phone. An app can show the number and help you find a better spot, but it cannot make the signal itself stronger.

Why is my internet slow when I have full bars?

Bars show how strong the signal is, not how busy the tower is. A busy tower or a noisy signal can give slow data even when the signal is strong.